Portfolio · 2026

KingshukDharThree machines for small farms in northern Bangladesh, built to work in mud, monsoon rain and village workshops

Projects
Susan · Boris · Martha
Focus
Field machines · sensing & control
Region
Northern Bangladesh
Mission
Save groundwater and farm labour
Built with
CAD, Python, a soldering iron, a notebook
PROJECT 01 / 03 — SUSAN
SolidWorksPython12 V motor valveMulti-depth sensing

Susan, an automated irrigation system

Reads soil moisture at several depths across a field and opens the water valve only when the field needs it. A button lets the farmer overrule the machine.

Design problem

Farms across northern Bangladesh pump groundwater for irrigation, and much of it goes onto fields that don't need it. The first version of Susan used one moisture sensor and one threshold, and it watered whenever the surface read dry. In the field, a farmer showed me that a "dry" plot was still wet underneath, because water from higher ground had collected below the surface where the sensor couldn't see it. The system was pumping water the crop didn't need.

“No need for water today.”

The farmer, checking the soil by hand

Process

  1. Built v1 on the workbench: a moisture probe, a twelve-volt motor-driven valve, Python control logic, and live readings on my phone.
  2. Field-tested it, and found the subsurface-water failure when the farmer checked the soil by hand.
  3. Spent two weeks following farmers with a notebook, mapping where water pools after rain, which corners dry first, and why the plot near the canal never needs water.
  4. Deleted the single moisture threshold. Redesigned the system with probes at several depths, spread across the field.
  5. Added a manual override button on the enclosure, and logged every override as a design input for the next revision.
Actuator
12 V motor valve
Sensing
3 probe depths
Control
Python
Override
Manual · logged
Drag to rotate · scroll or pinch to zoom
Susan, exploded
Click a part to see why it’s built that way

Parts · click one for the design decision

    PartKD-01 SUSAN
    MaterialMS post, ABS, PVC
    Unitsmm
    ProjectionThird angle
    Overall W×H×D—
    Tolerance±0.5 unless noted
    RevB · v2
    DrawnKD · 2026
    Outcome

    Version 2 holds water when the soil is wet below the surface, and judges a field from many points instead of one patch of dirt. Every farmer override goes into a notebook titled “Things Susan Got Wrong,” and that notebook now drives the design more than the sensor data does.

    PROJECT 02 / 03 — BORIS
    Fusion 360AutoCADSheet-metalMechanism analysis

    Boris, a low-cost rice harvesting attachment

    A front-mounted reaper that bolts onto the two-wheel power tillers farmers already own, cuts rice, and lays it in a neat row for bundling.

    Design problem

    Harvest falls in a two-week window, and in that window hiring labour gets scarce and expensive. Cutting by sickle takes about 80 person-hours per hectare. Combine harvesters cost far more than a smallholder can pay and sink in soft paddy fields. Farmers already own power tillers that sit unused during harvest, so the attachment had to run off the tiller's own pulley and be built by a village workshop.

    Process

    1. Surveyed three common tiller models and designed one mounting bracket that fits all of them, plus a belt take-off from the engine pulley.
    2. Sized a slider-crank drive in Fusion 360 for a 76.2 mm knife stroke at 480 strokes per minute, and checked the knife speed against stalk-cutting data.
    3. Added a vertical lug-belt conveyor and star wheels that carry cut stalks to one side and lay them in a windrow.
    4. Drew every flat part in AutoCAD as 3 mm mild-steel plates that a local plasma or gas cutter can make, using only standard bearings and V-belts.
    5. Tested it on 0.5 ha of transplanted rice and measured shattering losses on ground sheets.
    Cutting width
    1.2 m
    Field capacity
    0.2 ha/h
    Grain loss
    1.8 %
    Build cost
    BDT 48k ≈ $400
    Drag to rotate · scroll or pinch to zoom
    Boris, exploded
    Click a part to see why it’s built that way

    Parts · click one for the design decision

      PartKD-02 BORIS
      MaterialMS 3 mm, EN8 knife
      Unitsmm
      ProjectionThird angle
      Overall W×H×D—
      Tolerance±1.0 · bearing seats ±0.05
      RevB
      DrawnKD · 2026-04
      Outcome

      One operator harvested 0.5 ha in 2.5 hours, which would take about 40 person-hours by sickle. A local workshop built a second unit from the drawing set alone, and the build cost came in under one season's hired-labour bill for 2 ha.

      PROJECT 03 / 03 — MARTHA
      OnshapeFEALathe workUser testing

      Martha, an improved hand-pump mechanism

      A retrofit kit for the standard No. 6 suction hand pump that cuts handle force by a third and stops the pin wear that leaves village pumps broken.

      Design problem

      Shallow tube wells with No. 6 cast-iron pumps supply drinking water to millions of households. They are hard on the people who use them most, often women and children, and the steel pin in the handle wears an oval hole within months. Once it does, each stroke loses travel and the pump needs more strokes for every bucket. The fix had to fit existing pump heads without welding and cost less than a new pump.

      Process

      1. Measured handle force with a luggage scale and counted strokes per 15 L bucket at six village pumps.
      2. Modelled the pump head in Onshape and moved the pivot to raise the lever ratio from 1:6.5 to 1:9.5, keeping the full piston stroke.
      3. Replaced the bare pin with a sealed 6202 ball bearing in a bolt-on clamp, and ran FEA on the handle at 2× the peak user load.
      4. Turned a PVC piston with double nitrile cup seals to replace the leather washer, which stiffens when it dries out.
      5. Fitted the kit to two community pumps and logged force, strokes and repairs for 90 days.
      Handle force
      118 N (was 176 N)
      Lever ratio
      1 : 9.5
      Discharge
      32 L/min at 6 m
      Kit cost
      BDT 1,350 ≈ $11
      Drag to rotate · scroll or pinch to zoom
      Martha, exploded
      Click a part to see why it’s built that way

      Parts · click one for the design decision

        PartKD-03 MARTHA
        MaterialCast iron, MS, PVC, NBR
        Unitsmm
        ProjectionThird angle
        Overall W×H×D—
        Tolerance±0.2 · bearing bore H7
        RevD
        DrawnKD · 2025-12
        Outcome

        After 90 days, users needed 34% less force and 11% fewer strokes per bucket, and neither pump needed a repair. Before the kit, the same pumps averaged one pin or washer repair every 7 weeks. Children aged 10–12 could fill a bucket without using both hands.

        Toolkit

        Section 04

        SolidWorks

        Irrigation enclosure, valve and probe assemblies.

        A-01

        Fusion 360

        Slider-crank and conveyor mechanisms, sheet-metal parts.

        A-02

        Onshape

        Retrofit parts modelled around measured castings, plus FEA.

        A-03

        AutoCAD

        Flat-pattern drawings that village workshops can cut and weld from.

        A-02 · A-03
        Also PythonSoldering & wiringSoil-moisture sensingFDM printingPlasma & gas cuttingLathe workFarmer interviewsField trials & data logging